Fluid-components-international ST50 Uživatelský manuál

Procházejte online nebo si stáhněte Uživatelský manuál pro Zařízení Fluid-components-international ST50. Fluid Components International ST50 User Manual Uživatelská příručka

  • Stažení
  • Přidat do mých příruček
  • Tisk
  • Strana
    / 36
  • Tabulka s obsahem
  • KNIHY
  • Hodnocené. / 5. Na základě hodnocení zákazníků
Zobrazit stránku 0
This page is subject to proprietary rights statement on last page
Pre-Installation
The ST50 can be specified with integral or remote electronics. The flow element has a serial number etched into the side of the
extension pipe as shown on figure A. The transmitter circuit card has a serial number noted on the board as shown in figure B. The
flow sensor and transmitter circuit have been calibrated as a matched set and should be paired together in service unless otherwise
approved by a factory technician.
Flow Direction Alignment
All sensor elements have a flow arrow indicator marked on the element assembly at the reference flat. These flow elements have
been calibrated in a particular direction and are designed to be used in service with the flow arrow facing in the same direction as
flow in the pipe stream. See Appendix C for orientation and factory calibration details.
ST50 MASS FLOW METER
Installation and Operation Guide
Recommended Straight Run
To optimize flow meter system performance, FCI recommends installation with a minimum of 20 pipe diameters upstream straight
run and 10 pipe diameters of downstream straight run. Where straight run limitations significantly reduce the available pipe diam-
eters, FCI utilizes Vortab flow conditioners to produce a transferable flow profile from the calibration installation to actual field
installations. FCI’s proprietary AVAL software is available to make flow meter installation evaluations where straight run limitations
are considered. See Fig C for recommended installation.
FCI Flow Meters may be installed with less than the recommended straight run, but may have performance limitations. FCI offers
Vortab flow conditioners for use in applications that have significant straight run limitations. FCI uses the AVAL application
modeling software to predict meter performance in each installation. AVAL outputs are available to review prior to order placement
and will indicate performance expectations both with and without Vortab Flow Conditioning.
Figure C
Figure A
Figure B
Flow Direction
Serial Number
FLOW
Zobrazit stránku 0
1 2 3 4 5 6 ... 35 36

Shrnutí obsahu

Strany 1 - ST50 MASS FLOW METER

This page is subject to proprietary rights statement on last pagePre-InstallationThe ST50 can be specified with integral or remote electronics. The fl

Strany 2 - Flow Transmitter

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page10 D

Strany 3 - Installing Flow Element

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page11 Doc. No. 06EN003367 Rev. DExam

Strany 4 - Instrument Wiring

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page12 D

Strany 5 - VAC Input Power IO board

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page13 Doc. No. 06EN003367 Rev. DThe

Strany 6 - C00956-1

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page14 D

Strany 7 - ST50 Pulse Output (Sink)

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page15 Doc. No. 06EN003367 Rev. DAppl

Strany 8 - Setup Interface

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page16 D

Strany 9

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page17 Doc. No. 06EN003367 Rev. DHard

Strany 10

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page18 D

Strany 11

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page19 Doc. No. 06EN003367 Rev. DTran

Strany 12

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page2 Doc

Strany 13 - Maintenance

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page20 D

Strany 14 - INTENTIONALLY LEFT BLANK

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page21 Doc. No. 06EN003367 Rev. DAppe

Strany 15

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page22 D

Strany 16

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page23 Doc. No. 06EN003367 Rev. DAppe

Strany 17

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page24 D

Strany 18

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page25 Doc. No. 06EN003367 Rev. DNOTE

Strany 19 - REFERENCE

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page26 D

Strany 20

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page27 Doc. No. 06EN003367 Rev. DAppe

Strany 21 - Information

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page28 D

Strany 22

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page29 Doc. No. 06EN003367 Rev. DINTE

Strany 23 - Appendix B - List Commands

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page3 Doc. No. 06EN003367 Rev. DInstal

Strany 24 - Command Line Password: 357

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page30 D

Strany 25

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page31 Doc. No. 06EN003367 Rev. DAppe

Strany 26

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page32 D

Strany 27 - Appendix C - Drawings

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page33 Doc. No. 06EN003367 Rev. DVisi

Strany 28 - FLUID COMPONENTS

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page34 D

Strany 29

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page35 Doc. No. 06EN003367 Rev. DGood

Strany 30

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCDoc. No. 06EN003367 Rev. DFluid Components International LLC (FCI) All Rights ReservedNotice of Propr

Strany 31 - Appendix D - Customer Service

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page4 Doc

Strany 32

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page5 Doc. No. 06EN003367 Rev. DVAC Po

Strany 33 - RA #___________

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page6 Doc

Strany 34 - FCI Document No. 05CS000004C

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page7 Doc. No. 06EN003367 Rev. DOutput

Strany 35 - Instrument Warranty

FLUID COMPONENTS INTERNATIONAL LLC ST50 MASS FLOWThis page is subject to proprietary rights statement on last page8 Doc

Strany 36 - Notice of Proprietary Rights

ST50 MASS FLOW FLUID COMPONENTS INTERNATIONAL LLCThis page is subject to proprietary rights statement on last page9 Doc. No. 06EN003367 Rev. DIf the

Komentáře k této Příručce

Žádné komentáře